СИСТЕМИ ЗА КОНТРОЛ НА ДОСТЪПА
KaDe Access Control System

KDH-KS2012-IP
STANDARD CONTROLLER
The standard KDH-KS2012-IP series controller is designed for use in an access control system controlled by KaDe Premium Plus II software. The readers can use any identification technology provided they accept the Wiegand 26-40 bit interface.
Model KDH-KS2012-IP can control:
1 door - bi-directional
2 doors - one way

KDH-KS2024-IP
STANDARD CONTROLLER
The standard KDH-KS2024-IP series controller is designed for use in an access control system controlled by KaDe Premium Plus II software. The readers can use any identification technology provided they accept the Wiegand 26-40 bit interface.
The model KDH-KS2024-IP can control:
2 doors - bi-directional
4 doors - one way

KDH-KS2012-RS
STANDARD CONTROLLER
The standard KDH-KS2012-RS series controller is designed to be used in an access control system controlled by KaDe Premium Plus II software. The readers can use any identification technology provided they accept a 26-40 bit Wiegand interface.
The model KDH-KS2012-RS can control:
1 door - bi-directional
2 doors - one way

KDH-MOD2000INOUT
EXPANDER MODULE
Expansion module with 4 inputs for additional readers and 8 outputs (4 relay+4 transistor)
This module is compatible with standard KS2000 series and KS3000 series controllers with firmware 10.1.

KDH-MOD2000-ELV
EXPANDER MODULE
Модулът за разширение KDH-MOD2000-ELV увеличава броя на етажите, поддържани от контролера KDH-KS2000-IP-ELV.
Този модул е съвместим с програмата за надзор NMS AC само версия
3.00.XX
или KaDe Premium Plus II.

KDH-KS2000-IP-ELV
ELEVATOR CONTROLLER
Контролерът за асансьор KDH-KS2000-IP-ELV е проектиран да работи в системи за контрол на достъп под програмите за наблюдение NMS AC (версия 3.00.XX) или KaDe Premium Plus II. Четците могат да ползват всяка технология за идентификация, при условие че имат интерфейс Wiegand. Контролерът може да работи до 5 етажа, до 9 етажа с един разширителен модул KDH-MOD2000-ELV и до 69 етажа с 4 разширителни модула KDH-MOD2016-ELV . Контролерът има вграден IP порт за комуникация с управляващата програма и RS485 порт за комуникация само с разширителните модули.

KDH-MOD2016-ELV
EXPANDER MODULE
Модулът за разширение KDH-MOD2016-ELV увеличава броя на етажите, поддържани от контролера KDH-KS2000-IP-ELV. Използването на 4 модула от този тип позволява управление на до 69 етажа от един асансьорен контролер.
Този модул е съвместим с програмата за контрол на достъп NMS AC само версия
3.00.XX
и KaDe Premium Plus II.

KDH-KZ2000-IP-M
INTEGRATED ACCESS CONTROLLER
The KDH-KZ2000-IP-U_M is designed for access control and wall mounting. A 32 bit processor ensures fast and reliable data processing. It is a single door controller. An additional reader can be connected to it to control a door bilaterally. It is possible to set one of four identification modes: card only ; PIN only; card or PIN; card + PIN
The KDH-KZ2000-IP-U_M can operate in stand-alone mode (keypad programming) or in network mode. In network mode it can work online or offline. Compatible with KaDe Premium Plus. Works with MIFARE 13.6 MHz cards

KDH-KZ2000-IP-U
INTEGRATED ACCESS CONTROLLER
is designed for access control system and wall mounting. A 32 bit processor ensures fast and reliable data processing. It is a single door controller. An additional reader can be connected to it to control a door bilaterally. It is possible to set one of four identification modes: card only ; PIN only; card or PIN; card + PIN
The KDH-KZ2000-IP-U_M can operate in stand-alone mode (keypad programming) or in network mode. In network mode it can work online or offline. Compatible with KaDe Premium Plus. Works with UNIQUE 125kHZ cards

KDH-KZ330U/H/M-BLACK
INTEGRATED ACCESS CONTROLLER
The KDH-KZ330U/H/M is a multifunctional stand-alone controller for a single door. The controller supports up to 600 users (598 normal users + 2 panic users). Access is by : card, PIN, card + PIN or multiple card/PIN access. There are additional features including "Interlocking". Supports Wiegand 26~37 bits interface. Compatible with UNIQUE, HID®, PROX, MIFARE® cards (125kHZ+13.6MhZ

KDH-KZ730U/H
INTEGRATED ACCESS CONTROLLER
The KDH-KZ730U/H is designed for physical access control of a single door. It has a relay lock output that supports even electromagnetic locks with high current consumption. The Wiegand interface allows the connection of an external reader to implement two-way access control.
A vandal-resistant metal housing made of zinc alloy and IP66 rating allows the controller to be used for outdoor installation as well. The KDH-KZ730U/H allows different ways to authorize users: card, PIN, card or PIN, card and PIN, multiple card/PIN access. The device can also operate in reader mode with Wiegand interface. It supports Unique and HID Prox cards operating at 125 kHz frequency.

KDH-KZ630U/H
INTEGRATED ACCESS CONTROLLER
The KDH-KZ630U/H is designed for physical access control of a single door. It has a relay lock output that supports even electromagnetic locks with high current consumption. The Wiegand interface allows the connection of an external reader to implement two-way access control.
A vandal-resistant metal housing made of zinc alloy and IP66 rating allows the controller to be used for outdoor installation as well. The KDH-KZ630U/H allows different ways to authorize users: card, PIN, card or PIN, card and PIN, multiple card/PIN access. The device can also operate in reader mode with Wiegand interface. Supports Unique and HID Prox cards operating at 125 kHz frequency.
Supports Unique and HID Prox cards operating at 125 kHz

KDH-KAB200U-BLACK
INTEGRATED ACCESS CONTROLLER
A wireless access control for a door that consists of a wireless keypad, a mini controller and a wireless exit button. TEA+ Rolling Code's encryption algorithm and split design ensures a high level of security. The keypad can store up to 500 pins/users per card. Due to the extremely low power consumption, the keypad and exit button can operate for up to one year (based on 30 times per day) with only 3 AAA batteries and 1 Li-battery. Battery drop indication. Compatible with UNIQUE 125kHZ cards
ACCESS CONTROL SOFTWARE KADE PREMIUM II
The software is designed to work with standard KDH-KS2012/24-IP/RS controllers, KDH-KS2000-IP-ELV elevator controllers and KDH-KZ2000-IP-U or KDH-KZ2000-IP-M integrated controllers in online mode.
The KaDe Premium Plus II software is very easy to install and has a very user-friendly graphical interface. The "Dynamic Help" windows displayed on the operator's desktop are noteworthy as a user-friendly guide. After clicking any field on the operator's desktop, a description of that item and how to configure the system item is displayed.
The software is designed for small to medium sized companies.
The user interface allows:
- configuration of the physical elements of the system;
- definition of logical elements;
- "on-line" monitoring of the system through graphical object maps and alerts;
- displaying a picture of the user after using the map;
- generation of filtered event reports and saving in .xls format
The KaDe Premium Plus II software offers a host of features to meet the unusual requirements of the system administrator, such as:
- multi-card access;
- first-in access mode;
- access after operator confirmation;
- access control to elevators up to 69 floors;
- system element icon cards.
RS-485 lines on controllers can connect to PC software via RS-232 converter or TCP converter. The software can support up to 20 lines with 32 controllers on each bus. Controllers with an IP port can communicate over an Ethernet network. The system can support up to 1024 controllers, i.e. up to 4096 one-way controlled doors with 4 door controllers.

KDH-MODBOX
METAL BOX
Metal box for controllers and expansion modules.

NMS AC Access control system

KDH-KS3012-IP
CONTROLLER
The KDH-KS3012-IP is designed to work with the new NMS AC access control system. Communication with the system server is via TCP/IP protocol through the controller's Ethernet port.
It is possible to connect up to two readers to the controller using the Wiegand ports. Readers with output from 26 to 40 bits are supported. This ensures that the KDH-KS3012-IP controller can control one double-sided or two single-sided access controlled doors.
Support for readers with four-bit keypad output format allows the use of different ways to identify the user - card only, PIN only, card or PIN and two-step card and PIN identification.
The KDH-KS3012-IP has NO/NC programmable inputs and relay outputs to control the operation of devices with significant current ratings (e.g., solenoid locks, annunciators). The number of controller inputs and outputs can be increased by using the optional KDH-MOD2000INOUT expansion module for controllers with firmware 10.1 or KDH-MOD3000INOUT for controllers with firmware higher than 10.1.
The memory of 20,000 cards, 50,000 events and 20,000 alarms allows the system to operate uninterrupted even if communication with the server is lost, as well as backing up events and alarms to the server after reconnection.

KDH-KS3024-IP
CONTROLLER
The KDH-KS3024-IP is designed to work with the new NMS AC access control system. Communication with the system server is via TCP/IP protocol through the controller's Ethernet port.
It is possible to connect up to two readers to the controller using the Wiegand ports. Readers with output from 26 to 40 bits are supported. This ensures that the KDH-KS3012-IP controller can control one double-sided or two single-sided access controlled doors.
Support for readers with four-bit keypad output format allows the use of different ways of user identification - card only, PIN only, card or PIN and two-step card and PIN identification.
The KDH-KS3024-IP has NO/NC programmable inputs and relay outputs to control the operation of devices with significant current ratings (e.g., solenoid locks, annunciators). The number of controller inputs and outputs can be increased by using the optional KDH-MOD2000INOUT expansion module for controllers with firmware 10.1 or KDH-MOD3000INOUT for controllers with firmware higher than 10.1.
The memory of 20,000 cards, 50,000 events and 20,000 alarms allows the system to operate uninterrupted even if communication with the server is lost, as well as backing up events and alarms to the server after reconnection.

KDH-MOD3016 ELV
EXPANDER MODULE
The KDH-MOD3016-ELV expansion module increases the number of floors supported by the KDH-KS3000-IP-ELV controller. The use of 4 modules of this type allows up to 69 floors to be controlled from one elevator controller.

KDH-KS3000-IP ELV
ELEVATOR CONTROLLER
The KDH-KS3000-IP-ELV elevator controller is designed for operation in access control systems under NMS AC (version 4.00.02). All readers supporting Wiegand interface are compatible. The controller can control up to 5 floors, up to 9 floors with one KDH-MOD3004-ELV expansion module and up to 69 floors with 4 KDH-MOD3016-ELV expansion modules. The controller has a built-in IP port for communication with the control program and an RS485 port for communication with the expansion modules only.

KDH-MOD3000INOUT
EXPANDER MODULE
Expansion module with 4 inputs for additional readers and 8 outputs (4 relay+4 transistor)
This module is compatible with KS3000 series controllers with firmware higher than 10.1.

KDH-MOD2000INOUT
EXPANDER MODULE
Expansion module with 4 inputs for additional readers and 8 outputs (4 relay + 4 transistor)
This module is compatible with standard KS2000 series and KS3000 series controllers with firmware 10.1.

KDH-MOD3004-ELV
EXPANSION MODULE FOR ELEVATORS
Модулът за разширение KDH-MOD3004-ELV увеличава броя на етажите, поддържани от контролера KDH-KS3000-IP-ELV.
Този модул е съвместим с NMS AC
4.02.XX
версия или по-нова.

KDH-KZ3000FP-IP-M
INTEGRATED CONTROLLER
The KDH-KZ3000FP-IP-U_M controller is designed for wall-mounted access control system without additional housing. 32-bit processor provides fast and reliable data processing. It is a single door controller. With an optional reader (also with keypad) it is possible to set one of eleven identification modes: card only, PIN only, card or PIN, card+ PIN, fingerprint only, fingerprint or card, fingerprint+ card, fingerprint+ card+ PIN, fingerprint or PIN , fingerprint+ PIN, fingerprint or card or PIN.
The KDH-KZ3000FP-IP-M can operate in network mode, online or offline, and is compatible with NMS AC access control software.

KDH-KZ3000FP-IP-U
INTEGRATED CONTROLLER
The KDH-KZ3000FP-IP-U controller is designed for wall-mounted access control system without additional housing. 32-bit processor provides fast and reliable data processing. It is a single door controller. With an optional reader (also with keypad) it is possible to set one of eleven identification modes: card only, PIN only, card or PIN, card+ PIN, fingerprint only, fingerprint or card, fingerprint+ card, fingerprint+ card+ PIN, fingerprint or PIN , fingerprint+ PIN, fingerprint or card or PIN. Works with Unique cards 125 Khz
The KDH-KZ3000FP-IP-U can operate in network mode, online or offline, and is compatible with NMS AC access control software.

KDH-KZ3000-IP-M
INTEGRATED CONTROLLER
The KDH-KZ2000-IP-U_M controller is designed for an access control system and for wall mounting without an additional box. A 32 bit processor ensures fast and reliable data processing. It is a single door controller. With an optional reader (also with keypad) it can be used for two-way control. It is possible to set one of four identification modes: card only (default mode); PIN only; card or PIN; card + PIN
The KDH-KZ2000-IP-U_M can operate in stand-alone mode (keypad programming) or in network mode. In network mode it can operate online or offline with KaDe Premium Plus Software II supervisor on a PC.

KDH-KZ3000-IP-U
INTEGRATED CONTROLLER
The KDH-KZ3000-IP-U controller is designed for an access control system and for wall mounting without an additional box. A 32 bit processor ensures fast and reliable data processing. It is a single door controller. With an optional reader (also with keypad) it can be used for two-way control. It is possible to set one of four identification modes: card only (default mode); PIN only; card or PIN; card + PIN
Works with Unique 125 Khz cards
The KDH-KZ3000-IP-U can operate in stand-alone (keypad programming) or network mode. In network mode it can operate online or offline and is compatible with NMS AC access control software.

KDH-TA500CFP-IP-U/M/D
TIME ATTENDANCE TERMINAL
Time and attendance and access control terminal compatible with NMS AC access control software. The user can identify themselves with Unique, Mifare Classic, Mifare Desfire cards or fingerprint.
The terminal has a colour display with 8 function buttons. There is memory for 10,000 cards, 8,000 fingerprints and 200,000 events. It supports TCP/IP communication and their USN port. Atipassback function.
WARNING! A USB programmer model KDH-CADM500-FP is required to enter fingerprints into the system.

KDH-TA500C-IP-U/M/D
TIME ATTENDANCE TERMINAL
Time and attendance and access control terminal compatible with NMS AC access control software. User can identify with Unique, Mifare Classic, Mifare Desfire cards. The terminal has a colour display with 8 function buttons. It has memory for 50000 users, 150000 events. It supports TCP/IP communication and has a USN port. Atipassback function.
NMS ADVANCED CONTROL
ACCESS CONTROL SOFTWARE
NMS ADVANCED CONTROL is a new software designed for physical access control systems. It works with standard KDH-KS3012-IP, KDH-KS3024-IP, KDH-KZ3000FP-IP and KDH-KZ3000-IP controllers. Thanks to the client-server architecture, it is possible to manage from multiple workstations (2 stations are free with the license).The system is easy to install and has an intuitive graphical user interface. Through NMS AC the operator has the possibility to: - define system parameters (create operator permissions, licenses, copies);
- configuration of physical parameters of system components (controllers, doors, readers);
- define logical elements (schedules, access levels, tabs);
- defining scenarios that react automatically to system events;
- online monitoring of system status using system element icons located on site maps (with hierarchical structure), and through messages displayed in the event stack;
- viewing user snapshots after using the map;
- display images from cameras located in controlled door areas - automatically after an event or when the icon is clicked;
- floor access control via a reader located in the elevator car
- access control to lockers in changing rooms - up to 69 with one set of controller, modules and reader
- generation of filtered event reports (automatically or on demand) and saving in csv or html format (with the option to print to pdf);
The NMS AC also offers a number of features such as: access after using 2, 3 or 4 cards, opening a controlled door using a so-called "first opening card" with special permissions, access after operator confirmation, lockout and back pass protection in the controller. etc.
IP controllers communicate with the server via Ethernet. In the current software version the system can manage up to 128 controllers (8 with a free license. If more controllers are needed, expansion licenses are purchased).
Off-the-shelf computer configurations suitable for servers and workstations are available with Windows 10 licensed and NMS AC software configured.
For more information contact our sales department
Readers, programmers and cards

KDH-C130M-BLACK
READER FOR CONTACTLESS MIFARE 13.6 MHz CARDS
The KaDe 130 series brushes integrate perfectly into any interior - traditional or more modern.The durable ABS plastic housing and IP66 protection allow the KaDe 130 series brushes to be installed both indoors and outdoors. The readers support the most common Wiegand output interface, allowing them to be used in virtually any access control system. Built-in audio visual annunciators, a buzzer and a green/red LED, can be connected to the outputs of the corresponding access controller. This allows the generation of audible and visual signals according to the type of event configured in the access control system.

KDH-C130U-BLACK
UNIQUE 125KHz CARD READER
The KaDe 130 series brushes integrate perfectly into any interior - traditional or more modern.The durable ABS plastic housing and IP66 protection allow the KaDe 130 series brushes to be installed both indoors and outdoors. The readers support the most common Wiegand output interface, allowing them to be used in virtually any access control system. Built-in audio visual annunciators, a buzzer and a green/red LED, can be connected to the outputs of the corresponding access controller. This allows the generation of audible and visual signals according to the type of event configured in the access control system.

KDH-CK130M-BLACK
READER FOR MIFARE 13.6 MHz CARDS WITH KEYPAD
The KaDe 130 series brushes integrate perfectly into any interior - traditional or more modern.The durable ABS plastic housing and IP66 protection allow the KaDe 130 series brushes to be installed both indoors and outdoors. The readers support the most common Wiegand output interface, allowing them to be used in virtually any access control system. The built-in keypad allows other authorization methods besides RFID card reading. Access can be by PIN or a combination of card and PIN.

KDH-CK130U-BLACK
READER FOR UNIQUE 125KHz CARDS WITH KEYPAD
The KaDe 130 series brushes integrate perfectly into any interior - traditional or more modern.The durable ABS plastic housing and IP66 protection allow the KaDe 130 series brushes to be installed both indoors and outdoors. The readers support the most common Wiegand output interface, allowing them to be used in virtually any access control system. The built-in keypad allows other authorization methods besides RFID card reading. Access can be by PIN or a combination of card and PIN.

KDH-C130M-7UID
READER FOR CONTACTLESS MIFARE PLUS 13.6MHz CARDS
The reader allows reading the full identification number (7UID) from Mifare Plus® and Mifare DESFire® cards. The durable ABS plastic housing and IP66 protection allow the KaDe 130 series readers to be installed both indoors and outdoors. The readers support the most common output interface, Wiegand, with the ability to read a 56-bit card number (7UID).The built-in audio visual annunciators, a buzzer and a green/red LED, can be connected to the outputs of the corresponding access controller. This allows the generation of audible and visual alerts according to the type of event configured in the access control system.

KDH-C330U/H/M-BLACK
UNIVERSAL PROXIMITY CARD READER
The KaDe 330 series brushes feature a clean and elegant design that fits into any interior.
Durable ABS plastic housing and IP66 protection allow the KaDe 330 series brushes to be installed both indoors and outdoors.
The readers support the most common Wiegand output interface, allowing them to be used in virtually any access control system.
Built-in audio visual annunciators, a buzzer and green/red LED, can be connected to the outputs of the corresponding access controller. This allows the generation of audible and visual signals according to the type of event configured in the access control system.
The 330 series readers are multi-format readers. They operate at 123 kHz and 13.56 MHz frequencies, allowing card numbers to be read in Unique (26 or 34 bit output), HID® Prox (26 or 37 bit output automatically) and MIFARE® (26 or 34 bit output) formats. This makes the system more flexible and allows more than one card to be used in the same physical access control facility as standard.

KDH-CK130M-7UID
READER FOR CONTACTLESS MIFARE PLUS 13.6MHz CARDS WITH KEYBOARD
The reader allows reading the full identification number (7UID) from Mifare Plus® and Mifare DESFire® cards. The durable ABS plastic housing and IP66 protection allow the KaDe 130 series readers to be installed both indoors and outdoors. The readers support the most common output interface, Wiegand, with the ability to read a 56-bit card number (7UID).The built-in audio visual annunciators, a buzzer and a green/red LED, can be connected to the outputs of the corresponding access controller. This allows the generation of audible and visual alerts according to the type of event configured in the access control system. The built-in keypad allows for other authorization methods besides RFID card reading. Access can be by PIN or a combination of card and PIN.

KDH-CK330U/H/M -IVORY
UNIVERSAL PROXIMITY READER WITH KEYPAD
The KaDe 330 series brushes feature a clean and elegant design that fits into any interior.
Durable ABS plastic housing and IP66 protection allow the KaDe 330 series brushes to be installed both indoors and outdoors.
The readers support the most common Wiegand output interface, allowing them to be used in virtually any access control system.
Built-in audio visual annunciators, a buzzer and green/red LED, can be connected to the outputs of the corresponding access controller. This allows the generation of audible and visual signals according to the type of event configured in the access control system.
The 330 series readers are multi-format readers. They operate at 123 kHz and 13.56 MHz frequencies, allowing the reading of card numbers in Unique (26 or 34 bits output), HID® Prox (26 or 37 bits output automatically) and MIFARE® (26 or 34 bits output) formats. This makes the system more flexible and allows more than one card to be used in the same physical access control facility as standard. The built-in keypad allows for other authorization methods besides RFID card reading. Access can be by PIN or a combination of card and PIN.

KDH-C150MQR
READER OF MIFARE CARDS AND QR CODE
A multi-function reader that allows the reading of a User Identification Number (UID) from Mifare Classic cards and a QR code from a smartphone display or printed on a piece of paper. Supports Wiegand interface(
26, 34 bit)

KDH-CADM500-FP
ПРОГРАМАТОР ЗА ДОБАВЯНЕ НА ПРЪСТОВИ ОТПЕЧАТЪЦИ
Биометричен четец за добавяне на пръстови отпечатъци, предназначен за терминал - KDH-TA500CFP-IP. Съвмести с NMS AC софтуер за контрол на достъп.

KDH-KZ6000FR-IP
REMOTE BODY TEMPERATURE MEASUREMENT TERMINAL WITH RECOGNITION FUNCTION FACE AND MASK
Detection of people with fever;
Contactless body temperature measurement with using infrared rays;
Content analysis based on Deep Learning
Configuring Door unlock mode;
Human-sounding voice prompt;
Web Server;
Detection of people not wearing masks;
Measurement accuracy to +/- 0.3°;
Alarm Outputs;
Storage data on SD card;
8-inch LCD touch screen;
Two-way Audio

KDH-CADM-U24-II
ENCODER FOR UNIQUE CARDS
The encoder is designed to facilitate the retrieval of card numbers into the KaDe database or similar programs.
This model is designed to read UNIQUE cards (125 kHz) only. The reader is equipped with a USB interface that allows you to connect it to a standard USB port on a PC with KaDe access control software installed. The reader can also be used for other applications because it can work with any editor or editable fields in various applications. After placing the card on the base of the reader, the card number is automatically read and displayed in the field where the cursor was. In the KaDe access control system, the reader is used as one of the options in the process of entering card numbers into the system database. This is the most convenient option, especially for a large number of cards.

KDH-CADM-M32-II
MIFARE CARD ENCODER
The encoder is designed to facilitate the retrieval of card numbers into the KaDe database or similar programs.
This model is designed to read only MIFARE cards (13.56 MHz). The reader is equipped with a USB interface that allows you to connect it to a standard USB port on a PC with KaDe access control software installed. The reader can also be used for other applications because it can work with any editor or editable fields in various applications. After placing the card on the base of the reader, the card number is automatically read and displayed in the field where the cursor was. In the KaDe access control system, the reader is used as one of the options in the process of entering card numbers into the system database. This is the most convenient option, especially for a large number of cards.

KDA-M1002
CONTACTLESS MIFARE CARD
Type: ISO card
Format: MIFARE®
Operating frequency: 13.56 MHz

KDA-U1001
CONTACTLESS UNIQE CARD
Type: ISO card
Format: UNIQUE
Operating frequency:125 kHz

KDA-U1002
CONTACTLESS UNIQE CARD
Type: ISO card
Format: UNIQUE
Operating frequency:125 kHz

KDA-MP1002
CONTACTLESS MIFARE CARD
Type: ISO card
Format: MIFARE Plus® х 2kB card, 7 UID Bytes
Operating frequency: 13.56 MHz

KDA-M1004
CONTACTLESS MIFARE BRACELET
Type: bracelet
Format: MIFARE®
Operating frequency: 13.56 MHz

KDA-U1004
CONTACTLESS UNIQUE BRACELET
Type: bracelet
Format: UNIQUE
Operating frequency:125 kHz

KDA-M1003
CONTAINTLESS MIFARE KEY RING
Type: key ring
Format: MIFARE®
Operating frequency: 13.56 MHz

KDA-U1003
CONTACTLESS UNIQUE KEY RING
Type: key ring
Format: UNIQUE
Operating frequency:125 kHz
Electromagnetic locks and push buttons

KDA-STRIKE12SO
ELECTROMAGNETIC STRIKE
Electromagnetic strike (NC) with the possibility of manual unlocking of the lock in the open state. Current consumption 570mA. Can be used in steel, aluminium, wood and PVC profiles, both internal and external, with the possibility of installation for left and right doors, as well as in vertical and horizontal position. The 4mm adjustment range facilitates installation and ensures precise adjustment of the electric counter to the handle lock.
Can be installed together with a counter plate:
KDA-BP130 - Counter plate, short, galvanized (130x25x3mm)
KDA-BP250 -Counter plate, long, galvanized (250x25x3mm)
Explanation of the symbols configuring the model:
S-fail-secure
R- fail-safe
N-low consumption
T- narrow
M- with microswitch
P- with memory
O- with unlock function

KDA-STRIKE12RN
ELECTROMAGNETIC STRIKE
Electromagnetic strike (NO) with low current consumption (260mA). It can be used in steel, aluminium, wood and PVC profiles, both internal and external, with the possibility of installation for left and right doors, as well as in vertical and horizontal position. The 4mm adjustment range facilitates installation and ensures precise adjustment of the electric counter to the handle lock.
Can be installed together with a counter plate:
KDA-BP130 - Counter plate, short, galvanized (130x25x3mm)
KDA-BP250 -Counter plate, long, galvanized (250x25x3mm)
Explanation of the symbols configuring the model:
S-fail-secure
R- fail-safe
N-low consumption
T- narrow
M- with microswitch
P- with memory
O- with unlock function

KDA-STRIKE12SP
ELECTROMAGNETIC STRIKE
Electromagnetic strike (NC). Current consumption 570mA. It can be used in steel, aluminium, wood and PVC profiles, both internal and external, with the possibility of installation for left and right doors, as well as in vertical and horizontal position. The 4mm adjustment range facilitates installation and ensures precise adjustment of the electric counter to the handle lock.
Can be installed together with a counter plate:
KDA-BP130 - Counter plate, short, galvanized (130x25x3mm)
KDA-BP250 -Counter plate, long, galvanized (250x25x3mm)
Explanation of the symbols configuring the model:
S-fail-secure
R- fail-safe
N-low consumption
T- narrow
M- with microswitch
P- with memory
O- with unlock function

KDA-STRIKE12SN-II
ELECTROMAGNETIC STRIKE
Electromagnetic strike (NC) with low current consumption (260mA). It can be used in steel, aluminium, wood and PVC profiles, both internal and external, with the possibility of installation for left and right doors, as well as in vertical and horizontal position. The 4mm adjustment range facilitates installation and ensures precise adjustment of the electric counter to the handle lock.
Can be installed together with a counter plate:
KDA-BP130 - Counter plate, short, galvanized (130x25x3mm)
KDA-BP250 -Counter plate, long, galvanized (250x25x3mm)
Explanation of the symbols configuring the model:
S-fail-secure
R- fail-safe
N-low consumption
T- narrow
M- with microswitch
P- with memory
O- with unlock function

KDA-LOCK180Z-II
ELECTROMAGNETIC LOCK
Type locking: without power normally open (NO)
Power consumption: 280 mA for 12VAC
Power supply: 12V DC
Dimensions: 170 x 39 x 24
Holding force for electromagnetic/maximum pressure: 160Kg
Mounting type: surface
Additional functions : door lock sensor (Hall sensor)

KDA-LOCK180P
ELECTROMAGNETIC LOCK
Type locking: without power normally open (NO)
Power consumption:6 300mA за 12VAC / 300mA за 24VDC
Power supply: 12V or 24VDC
Dimensions: 340 x 42 x 21
Holding force for electromagnetic/maximum pressure:: 180Kg
Mounting type: surface
Additional functions : for double doors

KDA-LOCK180ZW
ELECTROMAGNETIC LOCK
Type locking: without power normally open (NO)
Power consumption: 300mA for 12VAC / 150mA for 24VDC
Power supply: 12V or 24VDC
Dimensions: 190 x 32 x 22
Holding force for electromagnetic/maximum pressure:: 180Kg
Mounting type: built-in
Additional functions : door lock sensor (Hall sensor)

KDA-LOCK180W
ELECTROMAGNETIC LOCK
Type locking: without power normally open (NO)
Power consumption: 300mA for 12VAC / 150mA for 24VDC
Power supply: 12V or 24VDC
Dimensions: 190 x 32 x 22
Holding force for electromagnetic/maximum pressure:: 180Kg
Mounting type: built-in

KDA-LOCK350DZC
ELECTROMAGNETIC LOCK
Type locking: without power normally open (NO)
Power consumption: 480mA for 12VAC / 240mA for 24VDC
Power supply: 12V or 24VDC
Dimensions: 288x 55x 29
Holding force for electromagnetic/maximum pressure: 310Kg
Mounting type: surface
Additional functions : door lock sensor (Hall sensor), open door sensor.

KDA-LOCK280DZC-II
ELECTROMAGNETIC LOCK
Type locking: without power normally open (NO)
Power consumption: 480mA for 12VAC / 240mA for 24VDC
Power supply: 12V or 24VDC
Dimensions: 250x 47x 29
Holding force for electromagnetic/maximum pressure: 280Kg
Mounting type: surface
Additional functions : door lock sensor (Hall sensor), open door sensor.

KDA-LOCK500DZC-II
ELECTROMAGNETIC LOCK
Type locking: without power normally open (NO)
Power consumption: 600mA for 12VAC / 300mA for 24VDC
Power supply: 12V or 24VDC
Dimensions: 265x 71x 40
Holding force for electromagnetic/maximum pressure: 500Kg
Mounting type: surface
.

KDA-BOLT150
ЕЛЕКТРОМАГНИТЕН БОЛТ
Type locking: without power normally open (NO)
Power consumption: 1400mA/150 mA
Power supply: 12V DC
Dimensions: 200x 28 x36
Holding force for electromagnetic/maximum pressure: 160Kg
Mounting type: built-in

KDA-BU180
MOUNTING PLATE
Mounting plate type U for electromagnetic lock KDA-LOCK180Z-II..

KDA-BLZ280
MOUNTING PLATE
Set mounting plates type Z/L for electromagnetic lock KDA-LOCK280DZC-II

KDA-BLZ500-II
MOUNTING PLATE
Set mounting plates type Z/L for electromagnetic lock KDA-LOCK350DZC-II

KDA-BZL500-II
MOUNTING PLATE
Set mounting plates type Z/L for electromagnetic lock KDA-LOCK500DZC-II

KDH-EXIT1093
CONTACTLESS EXIT BUTTON
Type of contact: NO/NC/C
Dimensions: 80 x 32 x 23 mm
Mounting type: surface
Operating temperature: -20 до 50
Electronic control (power supply required): yes
Type: Contactless for outdoor installation
Capacity : 3A / 30VDC

KDH-EXIT1040
EXIT BUTTON
Type of contact: NO / C
Dimensions: 83 x 32 x 25 mm
Mounting type: surface
Operating temperature: -10 до 55
Electronic control (power supply required): yes
Type: button
Capacity : 3A / 36VDC

KDH-EXIT1060
EXIT BUTTON
Type of contact: NO/NC/C
Dimensions: 85 x 55 x 21 mm
Mounting type: surface
Operating temperature: 0 до 55
Electronic control (power supply required): yes
Type: touch, for indoor installation
Capacity : 3A / 30VDC

KDH-EXIT1030-P
EMERGENCY EXIT BUTTON
Emergency exit button with two pairs of C/NO/NC contacts.
Power supplies

KDH-ZAS12/6/17
POWER SUPPLY
The power supply unit is designed to power KaDe KS2000 and KS3000 series controllers. It guarantees an uninterruptible 12 V DC power supply. Backed up with a rechargeable battery. Space is provided in the box for a 12V 18Ah battery.
Power voltage: 110V-240 V AC
Power consumption: 1.52A@230V AC max.
Output voltage : 13,5V-13,7V DC
Output current: 5A + 1A for battery charging
Battery surge protection: yes

APSAAT5
POWER SUPPLY
The power supply unit is designed to power KaDe KS2000 and KS3000 series controllers. It guarantees an uninterrupted power supply with a direct current of 12 V. Backed up by a rechargeable battery. There is space for a 12V 7Ah battery in the box.
Power voltage: 176V-264 V AC
Power consumption: 0,45A@230V AC max.
Output voltage: 9,5V-13,8V DC
Output current: 2A + 0,5 for battery charging
Battery surge protection: yes

APSAAT4
POWER SUPPLY
The power supply unit is designed to power KaDe KS2000 and KS3000 series controllers. It guarantees an uninterrupted power supply with a direct current of 12 V. Backed up by a rechargeable battery. There is space for a 12V 7Ah battery in the box.
Power voltage: 176V-264 V AC
Power consumption: 0,72A@230V AC max.
Output voltage: 9,5V-13,8V DC
Output current: 4,5A + 0,5 for battery charging
Battery surge protection: yes